The Radavist

Last year, ENVE opened its doors to the public for an Open House event. Once inside, visitors took a tour of its Ogden, Utah facilities and were greeted by two-dozen custom bikes from builders across the globe. This year the pandemic forced ENVE to pivot a bit, holding a virtual tour and framebuilder showcase they’re calling the Builder Round-Up. We’re pleased to once again host this showcase, with two-part coverage, so read on below for a full breakdown on these Beautiful Bicycles along with a few teasers of new ENVE product…

I’m a diehard fan of tough and playful hardtails. My affinity probably started with an invincible brick of a Schwinn BMX back when I was 13. It eventually evolved—I ditched my full suspension bike for the first generation of Surly’s infamous Krampus, morphed into the slacker front and tighter rear of a Carver Gnarvester, eloped with Tony’s personal Breadwinner Goodwater for a week, and then fell in love with Cjell Monē’s La Roca.

Last year, ENVE opened its doors to the public for an Open House event. Once inside, visitors took a tour of its Ogden, Utah facilities and were greeted by two-dozen custom bikes from builders across the globe. This year the pandemic forced ENVE to pivot a bit, holding a virtual tour and framebuilder showcase they’re calling the Builder Round-Up. We’re pleased to once again host this showcase, with two-part coverage, so read on below for part two of a full breakdown on these Beautiful Bicycles along with a few teasers of new ENVE product…

Last year, ENVE opened its doors to the public for an Open House event. Once inside, visitors took a tour of its Ogden, Utah facilities and were greeted by two-dozen custom bikes from builders across the globe. This year the pandemic forced ENVE to pivot a bit, holding a virtual tour and framebuilder showcase they’re calling the Builder Round-Up. We’re pleased to once again host this showcase, with two-part coverage, so read on below for a full breakdown on these Beautiful Bicycles along with a few teasers of new ENVE product…

Over the past few years, I’ve found myself only riding 150mm travel hardtails and full suspensions with slackened front ends and steep seat tubes. In my mind, why would you want anything else? Then I moved to Santa Fe, where we have even bigger backcountry loops, steep climbs, and long, rocky descents. Yet, we also have sweeping, undulating XC trails. Suddenly, all those 150mm bikes are a little too much for a lot of the trails here, most of which are in my neighborhood. Then Chumba came to the rescue, sending along their Sendero 130mm 29er hardtail for me to review and I fell in love with XC bikes once again.

Read on for how this beauty of a bike handles our chunder and Chamisa-lined trails here in Santa Fe…

Where do we even begin here? Boone is what I would consider a friend. Someone I met years ago in Portland who is now in Bend and still doing what he loves: making rad shit. Right now, however, he’s making rad shit for himself. When he and I first met, he was working for Argonaut Cycles but that wasn’t his first framebuilding job. As with everyone making bike frames, there’s a story to tell, and that’s what we’re doing here today, so sit back, turn on some metal, and check out the wild shit inside Boone Metal Fab.

Hydraulic shifting? 13 speeds? What in tarnation?

That’s what was going through my head when I first saw Rotor’s 13-speed drivetrain kit at Sea Otter last year. The 1×13 kit is a follow up to Rotor’s Uno 2x groupset from four years ago. Like the Uno, the 1×13 uses hydraulically-actuated shifting for a groundbreaking industry first. As you might imagine, this tech is pricey, and probably not for everyone, myself included, but over the past few months, I’ve enjoyed riding it on this beautiful titanium chassis by none other than Merlin Bikes. Check out a full review of Rotor’s 1×13 and the Merlin Sandstone Gravel bike below.

This year was to be the first year Nao Tomii of Tomii Cycles was going to attend NAHBS. For a small builder like Nao, spending the kind of money it takes to pull a seat up to the table of the USA’s largest hand made bicycle show takes a lot of financial planning, so when NAHBS was postponed this year, Tomii Cycles wouldn’t be able to attend. Most builders display customer’s bikes at NAHBS and asking his clients to wait four more months for their bikes, especially during a pandemic was out of the question. I reached out to Nao and asked if we could display his bikes here at the Radavist, so we’re doing just that…

This year was to be the first year Nao Tomii of Tomii Cycles was going to attend NAHBS. For a small builder like Nao, spending the kind of money it takes to pull a seat up to the table of the USA’s largest hand made bicycle show takes a lot of financial planning, so when NAHBS was postponed this year, Tomii Cycles wouldn’t be able to attend. Most builders display customer’s bikes at NAHBS and asking his clients to wait four more months for their bikes, especially during a pandemic was out of the question. I reached out to Nao and asked if we could display his bikes here at the Radavist, so this week, we’re doing just that. Here’s Kevin’s Gravel Packer, complete with paint by Jordan Low and Andrew the Maker bags…

This year was to be the first year Nao Tomii of Tomii Cycles was going to attend NAHBS. For a small builder like Nao, spending the kind of money it takes to pull a seat up to the table of the USA’s largest hand made bicycle show takes a lot of financial planning, so when NAHBS was postponed this year, Tomii Cycles wouldn’t be able to attend. Most builders display customer’s bikes at NAHBS and asking his clients to wait four more months for their bikes, especially during a pandemic was out of the question. I reached out to Nao and asked if we could display his bikes here at the Radavist, so this week, we’re doing just that…

This year was to be the first year Nao Tomii of Tomii Cycles was going to attend NAHBS. For a small builder like Nao, spending the kind of money it takes to pull a seat up to the table of the USA’s largest hand made bicycle show takes a lot of financial planning, so when NAHBS was postponed this year, Tomii Cycles wouldn’t be able to attend. Most builders display customer’s bikes at NAHBS and asking his clients to wait four more months for their bikes, especially during a pandemic was out of the question. I reached out to Nao and asked if we could display his bikes here at the Radavist, so this week, we’re doing just that, beginning with Blake’s Gravel Hunter, complete with custom Andrew the Maker bags and a stunning paint job by Jordan Low. Sit back and enjoy clicking through these beautiful photos of an equally as beautiful bicycle…